Electric Fire Pump Controls - NO LONGER AVAILABLE

Hubbell Fire pump Motor Controllers are designed to comply with the latest standard of the National Fire Protection Association for the installation of stationary pumps for fire protection (NFPA-20).

• LXi Microprocessor Logic & Control
• Coordinated design engineered, built, tested and labeled by one manufacturer
• Suitable for use as service entrance equipment
• Full compliment of visual indicators
• Communications port
• LCD display shows simultaneous reading of all phases for amps and volts, and system pressure
• Full range of horsepower ratings and voltages
• Ample cable bending space

Return to top

Fire Pump Controls with Transfer Switch - NO LONGER AVAILABLE

Hubbell Fire pump Motor Controllers with Automatic Transfer Switches (ATS) are designed to comply with the latest standard of the National Fire Protection Association for the installation of stationary pumps for fire protection.

• LXi Microprocessor Logic & Control
• Coordinated design engineered, built, tested and labeled by one manufacturer
• Suitable for use as service entrance equipment
• Emergency source suitable for standby generator sets or optional dual utility sources

• Full compliment of visual indicators
• Communications port
• LCD display shows system pressure, and simultaneous reading of all phases for amps, volts and pressure
• Full range of horsepower ratings and voltages
• Ample cable bending space

Transfer Switch

Hubbell LX-450 automatic transfer switches provide dependable transfer of power between preferred and emergency power sources. The compact modular design is suitable for emergency and standby system applications and is available in 100 through 1250 amps in 2 or 3 pole configurations. The LX-450 transfer switches is UL 1008 listed to 480VAC and greatly exceed the UL requirements for withstand and closing.

Return to top

Diesel Fire Pump

The HD5000 Fire Pump Controllers are a microprocessor based combined automatic and manual diesel engine driven fire pump controller. These controllers are specifically designed and tested to start, and monitor fire pump diesel engines. They are available for use with 12 or 24 volt lead acid or NiCad batteries, and with an AC voltage input range of 115 or 220 volts, 50/60 Hertz. The HD5000 monitors, displays and records the fire pump system information.

Hubbell's fire pump controllers are Listed by Underwriters Laboratories Inc., in accordance with UL218, UL/cUL Listed, Approved by Factory Mutual, in accordance with FM 1321/1323, New York City MEA Approved, and available with CE. They are built to meet or exceed the requirements of NFPA 20 (Installation of Centrifugal Fire Pumps). NFPA 70 (National Electrical Code), as well as NEMA and the approving authorities.

Return to top

Alarm Panel

The LX-908 remote panels are designed to meet the NFPA 20 specifications requiring a remote alarm panel when the pump house or pump room is not constantly attended. These alarm panels can be used with electric motor driven or diesel engine driven fire pump controllers. The alarm panel should be installed in a location that is under supervision at all times.

LX-960b low suction pressure alarm and shutdown panels are designed to be used with electric and diesel engine driven fire pump controllers. They provide pump shutdown in the event a low suction pressure condition occurs. In addition, these panels provide audible and visible alarms for the following conditions:

• Control Power Available
• Low Suction Pressure
• Suction Pressure Normal

Return to top

Jockey Pump Control

Hubbell's Model LX-600 Jockey Pump Controllers are intended for across-the-line starting of squirrel cage motors up to 10 hp at 200/208V, up to 15 hp at 220/240V, and up to 25 hp at 440/480V. Larger hp sizes are available, consult factory. LX-600 controllers are for fire protection system applications where it is desirable to maintain uniform system water pressure by the use of an automatic pressure maintenance pump.

Model LX-600 Jockey Pump Controller serves over-all system efficiency by detecting minor fire protection water system leakage. By bringing jockey or make-up pumps on line, they maintain pressure within set point limits without unnecessary cycling of the main fire pump.

Return to top

Transfer Switch for loads other than fire pumps
(Consult factory for stand alone fire pump rated ATS)

Hubbell LX-450, LX-440 transfer switches provide dependable transfer of power between preferred and emergency power sources.  The compact modular design is suitable for emergency and standby system applications and is available in 100 through 1250 amps in 2, 3, and 4 pole configurations.  The LX-450 and LX-440 transfer switches are UL 1008 listed to 480VAC and greatly exceed the UL requirements for withstand and closing

Return to top